Request An Appointment

 

 

Right here below you will discover more incredibly good data related to A Step-by-Step Guide to Installing a Bathtub.

Mounting a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is easily accessible, the job can move easily; if you have to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have actually currently purchased a brand-new tub and also don't need to transform the arrangement of your previous water system pipelines.
Your tools and also material checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Preparing for the Installment

To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.

 

 

Removing Old Taps

If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Tub

Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water and examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub should wait till the bathtub has been used a minimum of once as this will resolve it right into its last position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous kind must be linked to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, resulting in issues with moisture and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to allow for the activity experienced when the tub remains in usage. The sealer can crack rather very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you like more info about Installing A Bathtub? Make a short review directly below. We would be delighted to see your insights about this page. Hoping that you come back again before long. I beg you set aside a second to distribute this content if you appreciated it. Thanks for going through it.

Book A Service Call